- 您现在的位置：买卖IC网 > Sheet目录1001 > PR308T11ESZ (Sharp Microelectronics)RELAY SSR 240VAC 8A TRIAC 4-SIP
PR308T11ESZ
■ Design Considerations
● Recommended Operating Conditions
Parameter
Symbol
Conditions
MIN.
MAX.
Unit
Input
Input signal current at ON state
Input signal current at OFF state
I F (ON)
I F (OFF)
?
?
20
0
30
0.1
mA
mA
Load supply voltage
Output Load supply current
Frequency
Operating temperature
V OUT (rms)
I OUT (rms)
f
T opr
?
Locate snubber circuit between output terminals
(Cs = 0.022 μ F, Rs = 47 ? )
?
?
80
0.1
47
? 20
240
I T (rms)
× 80%( ? )
63
80
V
mA
Hz
?C
( ? ) See Fig.2 about derating curve (I T (rms) vs. ambient temperature).
● Design guide
In order for the SSR to turn off, the triggering current (l F ) must be 0.1mA or less.
In phase control applications or where the SSR is being by a pulse signal, please ensure that the pulse width
is a minimum of 1ms.
When the input current (I F ) is below 0.1mA, the output Triac will be in the open circuit mode. However, if the
voltage across the Triac, V D , increases faster than rated dV/dt, the Triac may turn on. To avoid this situation,
please incorporate a snubber circuit. Due to the many different types of load that can be driven, we can
merely recommend some circuit vales to start with : Cs=0.022 μ F and Rs=47 ? . The operation of the SSR
and snubber circuit should be tested and if unintentional switching occurs, please adjust the snubber circuit
component values accordingly.
When making the transition from On to Off state, a snubber circuit should be used ensure that sudden drops
in current are not accompanied by large instantaneous changes in voltage across the Triac.
This fast change in voltage is brought about by the phase difference between current and voltage.
Primarily, this is experienced in driving loads which are inductive such as motors and solenoids.
Following the procedure outlined above should provide sufficient results.
Any snubber or Varistor used for the above mentioned scenarios should be located as close to the main out-
put triac as possible.
The load current should be within the bounds of derating curve. (Refer to Fig.2)
Also, please use the optional heat sink when necessary.
In case the optional heat sink is used and the isolation voltage between the device and the optional heat sink
is needed, please locate the insulation sheet between the device and the heat sink.
When the optional heat sink is equipped, please set up the M3 screw-fastening torque at 0.3 to 0.5N?m.
In order to dissipate the heat generated from the inside of device effectively, please follow the below sugges-
tions.
(a) Make sure there are no warps or bumps on the heat sink, insulation sheet and device surface.
(b) Make sure there are no metal dusts or burrs attached onto the heat sink, insulation sheet and device sur-
face.
(c) Make sure silicone grease is evenly spread out on the heat sink, insulation sheet and device surface.
Sheet No.: D4-A01901EN
8
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
PR308T21ESZ
RELAY SSR 240VAC 8A ZC 4-SIP
PR31MA11NTZ
RELAY SSR 240VAC .06A TRIAC 6DIP
PR32MA11NTZF
RELAY SSR 240V 150MA 6-DIP
PR33MF11NSZF
RELAY SSR 240VAC .3A 8-DIP
PR33MF51NSZF
RELAY SSR TRIAC OUT 300MA 8-DIP
PR36MF11NSZF
RELAY SSR 240VAC .6A TRIAC 8-DIP
PR36MF22NSZ
RELAY SSR 240VAC .6A ZC 8-DIP
PR39MF11NSZF
RELAY SSR 240VAC .9A TRIAC 8-DIP
相关代理商/技术参数
PR308T21ESZ
功能描述:RELAY SSR 240VAC 8A ZC 4-SIP RoHS:否 类别:继电器 >> 固态 系列:PR308T 其它有关文件:AQx REACH Cert of Compliance 特色产品:AQY Series Relays 标准包装:1 系列:PhotoMOS™ AQY 电路:SPST-NO（1 Form A） 输出类型:AC，DC（RF） 导通状态电阻:1.25 欧姆 负载电流:250mA 输入电压:1.3VDC 电压 - 负载:0 ~ 40 V 安装类型:表面贴装 端接类型:SMD（SMT）接片 封装/外壳:4-SMD（0.175"，4.45mm） 供应商设备封装:4-SSOP 包装:Digi-Reel® 继电器类型:继电器 其它名称:255-2683-6
PR-30C EURO
制造商:LENTEK 功能描述:PEST REPELLER, 3PK EURO
PR30N/CE
制造商:未知厂家 制造商全称:未知厂家 功能描述:STROMZANGE TYP PR30 ACDC 20A LEM
PR-31
制造商:NTE Electronics 功能描述:
PR3100A-25PQ160C
制造商:未知厂家 制造商全称:未知厂家 功能描述:Read/Write Buffer
PR3100A-33PQ160C
制造商:未知厂家 制造商全称:未知厂家 功能描述:Read/Write Buffer
PR3100A-40PQ160C
制造商:未知厂家 制造商全称:未知厂家 功能描述:Read/Write Buffer
PR31100
制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Highly integrated embedded processor